Here are a few photos from the 2016 NRA Collectors/HSCA Annual Meeting show taken Sunday, July 31:

left: Dan Rathgeber accepting his well deserved NRA award from HSCA member/NRA Director Lance Olson. Jim Supica of the NRA Museum is at left "supervising".

below: Dan Rathgeber with his NRA award at his Hi-Standard "H" and "G" Models display.

above: HSCA "staff photographer" Tom Bolander checking his photos of Dan's award and display.



Dan Rathgeber with his display and NRA Award at this year's meeting in Kansas City

HSCA Newsletter

The July 2016 HSCA Newsletter was mailed on July 1.

HSCA Display at Louisville NRA Meetings - 2016

 HSCA AT NRA  2016  - President jon Miller

HSCA set up a display at the NRA 2016 annual meeting  in Louisville
Kentucky.  Vice  President Steve Schrott proposed a theme of showing one of each of   
the major  types of High Standards produced by the company.   
We had derringers, revolvers, semi- automatic pistols,  a suppressed
pistol, rim-fire and center-fire rifles and even a UD-42.  The Olympic Slow fire
pistol designed  and produced by High Standard was also exhibited.  There was
a lot of history and diversity  in that 10’x10’ booth.
You would think there would be plenty of room to move  around in one
hundred square feet.  There could have been except for the constant flow of people   
stopping to  see the gun they grew up with or that some family member had
left them.  Then they started asking questions and  stayed a while to just
talk.
Steve wanted to show the diversity of High Standard  production and
accomplished it.  He  said he just wanted to start people talking and getting them
interested in High  Standards.  He certainly  succeeded.
Ken Rabeneck, John Stimson, Lee Horner and Jon Miller  also took turns
manning the booth and answering  questions.
It was really a great way to spend a weekend in  Louisville.  Next year’s
annual  meeting is in Atlanta.   
HSCA will hold its annual meeting at the MVACA/NRA Collectors show  in
Kansas City, Missouri in July.  We will have the exhibit there for your 
enjoyment.

L-R: John Stimson, Steve Schrott (sitting), Jon Miller

Tom (Lee) Horner

Steve "recharging"

HSCA Display at NRA-Louisville

Photos from the HSCA display at the NRA convention in Louisville, KY on May 20-21-22, 2016

Jon Miller's First High Standard

From Jon Miller:

Once upon a time in the early 1980s I was a member of the Tampa Police Pistol and Rifle marksmanship pistol team. I had done well and progressed rapidly to the expert class. But, I became stuck there. Despite hours of practice and literally thousands of rounds of club ammunition I could not break into the master class.

Coach Gunny Pitts took me aside and said it's not you, it's your pistol. You wore it out. I was still shooting a Ruger Mark I that had done well for 20 years in plinking and even hunting. It had however reached its limits.
Pitts took me to the armorer and explained the problem. I was issued a very very well used High Standard model 104 Supermatic Citation which had been donated to the club. Its previous owner had been a national champion, AMU and Olympic competitor. I cannot tell you how well used that pistol appeared. I was skeptical. but it had a good trigger and barrel. I trusted Gene Pitts. I signed for the pistol.

We started training that day. Within six months I received my master certification card. I continued to practice almost daily. My scores continued to rise. I began competing in International events too. Gradually I became concerned that I could wear out this gun, too. A High Standard Victor became available so I bought it for backup. After that, I bought another and another, Just in case.

My goal was to have one of each type of pistols High Standard produced. I have since learned that is naive as well as expensive. Too many models and too many variations. Just ask John Stimson.

I continued to use that first High Standard pistol through 2003. That year it won state championships in Indiana, Ohio, and Kentucky. I no longer shoot competitively. My sons did though. They both used that pistol to win Kentucky state championships.

The Tampa range has closed long ago but nobody asked for me to return the pistol so it still sits in my safe. (Just in case.) along with all the other High Standards I accumulated over the years.

Many years ago wife asked me why I needed so many guns. I told her I was collecting them as an investment for our son's college education. When tuition was due I would sell them off gradually. She rolled her eyes skyward and smiled. She's smart like that.

Hartford Arms - Catalogues & Advertisements

HSCA members:
The April, 2016 issue of the HSCA Newsletter was mailed on Wednesday, March 30.  There are over 100 photos in this issue.  Thank you to President jon Miller, Jim Gray, Bert Markel, Dick Baker, Marcia Mighell, John Stimson, Bill Jenkins, Mike Gallion, Tom Horner, Ralph Boineau, Steve Stafford, Jerry Watson and Steve Schrott for their contributions to this issue. The HSCA Newsletter is not possible without this group effort.

VARIOUS PARTS NEEDED FOR MODEL 9205 SHARPSHOOTER, MODEL 102 CIATATION AND MODEL B

I need the following parts for:

High Standard - Burgundy/Yellow Box for Model: 9205 Sharpshooter - Slant Grip with 5” Bull Barrel.

High Standard - Walnut Right Hand Thumb rest (Slant) Grips with or without HS Logo (Trigger or Whirlwind Logo for Model 9205 Sharpshooter)

Stabilizer for Model 102 Citation

Large (3-1/2 oz.) “Hump bottom” weight and side plates for Model 102 Citation

Black Grips for Early Model “B” 1a

If you have any of these parts please call at (931)-220-5832 or email at: jrrcflyer(at)charter(dot)net

Thank You,

John R. 

Very early Model B special features. Serial numbers for Model Bs started at 5000.
  I have picked up one of the first Model B s, Serial # 5062 that shows some of the special features that were parts from Hartford arms. This B has the Hartford front site and the magazine release from Hartford Arms that has surface cuts in both directions. The HS release only had cuts in one direction. In addition this B has the short extractor with the retaining pin that was used until it was changed to be retained by spring tention without a retaining pin.
 I have included a picture that shows the Front sight. The later pictures will follow to show release and extractor.

Model B or C parts Needed

Does anyone have a stop block (stop lug) for a Model B or C in used but serviceable condition they want to sell? It is for the second series with the take down lever on the right side. I also need the spring and plunger that pushes it upright. I'm putting a Model C back together for a friend of a friend, and some parts are missing. If you have these parts, email me at blog (at) whidbey (dot) com.

Thanks!

Mike G.

J C Higgins Model 88 Update

 

 

 

I have a Higgins Model 88 and a High Standard Sentinel that appear to have been made about the same time.

 According to John Stimson, High Standard put a coating over the anodizing on the aluminum frames to keep the finish from coming off.  The Model 88 appeared to have high gloss paint.  Most of that high gloss is gone from my gun.  The Sentinel appears to have a dull finish, but it is good.

 

 I had a lot of powder build up on the 88 from a previous owner.  I tried many products to remove it without much luck and ended up having to scrape it off. 

When scraping around where the barrel protrudes through the frame I ran into weld at the top of the barrel.  At first I thought it was powder build up, because the Sentinel was smooth in this area.

 

 

 

 

 

 

What I found out is that you should not use Gun Scrubber or Slip 2000 Carbon Killer on these frames.  They will take the coating off the frames of these guns.  I also wouldn't use these products on some of the High Standard Derringers have a similar coating.

Removal of Slide From H-D Military Pistol That Was Incorrectly Assembled

When a person puts the slide back onto the frame of a pistol without having the driving spring captured on a Type II takedown system, the slide stop will get caught in front of the retracting rod end and hung up in the coils of the driving spring. This results in the slide not moving normally, and not closing the slide fully. The way to fix this is to use a length of coat hanger wire that has a slight bend on the last 3/4 inch of the end (about 15 degrees) as a tool to compress the retracting rod and spring.  I used a pin collet handle to hold the wire.  

 

Pull the slide back and hold the breech face open about 0.9 inch from the barrel with a block so that the tool can be inserted into the small opening on the bottom of the left side of the slide between the hammer and frame.  I used a wooden splint (about 4"X1/2"X1/8") inserted into the magazine well with the top sticking out to block the slide open.  The tool should be inserted with the outside of the curve towards the top of the slide.  Insert the tool so that the end of the wire hits against the back of the retracting rod.  Push the retracting rod towards the barrel about an inch or so. You should feel the spring resistance.  Pushing the rod forward should cause the stop lug to be released from the coils. You should be able to see the takedown lever move down a little. Then you should be able to easily push down on the takedown lever to get the stop lug all the way down. You can remove the tool at this point. Then you can pull the slide off of the frame. After removing the slide, use a punch or other tool to push the retracting rod and spring forward so that the pickup spring button can be pressed, allowing the pickup spring to capture the retracting rod. When this is done, the slide can be reassembled to the frame in the normal manner. Of course, check the driving spring for damage and replace it if necessary.

The above process should work if the slide has not been forced back and forth a lot in attempts to get the slide removed.  If it does not work, it indicates the driving spring has been stretched and deformed to a point that the spring will not go all the way into the hole in the rear of the slide, and the retracting rod cannot be pushed far enough into the hole in the slide to release the stop lug from the spring coils and allow it to tip forward.  You can use the tool to push the stop lug forward to try to get it untangled from the spring coils.  Push down on the takedown lever while doing this until it goes all the way down, and hold it down while pulling the slide off.  Don't use too much force in pushing the lever down to prevent damage to the lever parts.  If that does not work, you can attempt to remove the spring by using a tool with a hook on the end to catch a coil of the spring and pull it out.  This will take a lot of effort to fish out the spring or pieces of spring, but can work.  These methods will take time and patience.  Once apart, the driving spring can be replaced with a new one, and the gun reassembled properly.  Careful work will allow the gun to be repaired without damaging the frame, slide, or other components aside from the driving spring.

 

Note:  Clicking on the photos will allow them to be viewed in larger size.





Retracting Rod Captured Properly.



Retracting Rod Not Captured. Note the position of the
takedown lever with the stop lug fully up.

 

Tool used to press retracting rod forward in slide.

 

This is how the tool should be used.

 

The rod can be moved forward to allow the stop lug to be released.

 

This is where the tool is inserted into the slide.

 

Wood splint used to block the slide open about 0.9 inch. Note the position of the
 takedown lever with the stop lug below the retracting rod.

 

Tool inserted into opening in bottom of slide and pushing rod forward.
Note the position of the takedown lever when the stop lug is fully down.

 

Push the takedown lever fully down and remove the tool.

 



Pull the slide off of the frame while holding down the takedown lever. 

Tip for Removing Sear Bar That is Stuck in Trigger Pivot Hole

High Standard pistols that have been stored for a long time may have dried oil residue and/or form some corrosion in the top hole of the trigger where the sear bar pin goes in.  This can make the trigger action very sluggish or even not be able to move the sear bar much at all.  Applying penetrating oil (i.e., Kroil) in the area may help free the pin so that the sear bar can be removed.  However, sometimes the sear bar needs some help in getting it apart.  The difficulty is that there is not much space between the sear bar and the frame to get a tool under the sear bar to assist in prying it out of the trigger.  One way to do this is to use dental floss under the sear bar as close to the pivot pin as possible and pull up on the sear bar with the floss.  The trigger can be moved back and forth while doing this to help free the pin from the hole in the trigger.  Once removed, the corrosion can be cleaned off the pin and trigger hole, the pin lubricated, and reassembled in the gun.  This should allow the pivot point to work easily.  The trick is to get the floss around the sear bar.  Start at the sear end of the bar, pry up the sear bar just enough to get the floss around the end of the bar.  Work it toward the pin end.  There is a pin boss in the frame where the sear bar has an opening that goes around the boss.  The floss will have to be pulled up over the boss to allow it to be pulled the rest of the way towards the pin end.  When the floss is as close to the pin as possible, pull the floss upwards while wiggling the trigger.  This should allow the pin to come out of the trigger hole.


Trigger and sear bar assembled




Trigger and sear bar



Remove side plate, safety, and U spring.

Start moving floss under sear bar at sear end.




Lift the floss over the pin boss.

Get the floss close to the pin.




Pull the floss upwards to remove the sear bar.

 

V-Suffix Marked Large Push Button Takedown High Standard Trophy Pistol

V-suffix serial numbered guns (V for visually impaired) were shipped in the final months (approximately June to October) of production in 1984 before High Standard ceased operations.  By taking previously rejected parts and putting together functional pistols and also previously rejected guns, they were able to use up many leftover parts and get as many guns out the door as possible.  These guns were sold as functional firearms, but had visual defects.  The V marked pistols were sold to distributors at a substantial discount.   I remember seeing ads in Shotgun News at the time for these V marked guns.  My memory is that they were being sold at about a 20% discount.  

I have a 5.5 inch barreled High Standard Trophy, serial number SH32422V.  It is a large push button framed gun that shipped in late summer of 1984, but it probably went to assembly in August/September, 1983. 

The normal means of attaching the barrel to the frame on the 108/SH series pistols was by the use of a socket head screw rather than the large push button used on the series 102 through 107 pistols.  The SH prefix serial numbered guns were sold in the 1981 to 1984 timeframe.  There are some older serial number types also found to have shipped during this time.

Note: the SH series designation was popularized by Tom Dance in his book, but is also used in the Blue Book of Gun Values, so both 108 series and SH series are used to describe this series. 

There were apparently several push button frames that had been rejected but still retained in inventory.  These frames were used to make serviceable guns and shipped during last months of shipments.  I have seen photos of other push button SH serial number with V suffix marked pistols with similar configuration as this one.  Pistols using these frames were a small number of the total of the V marked guns. 

The attachment method for the rear bridge sight base on this pistol is different than normal.  There are two screws holding the sight base onto the frame rather than the normal method of using a two piece rivet and a small roll pin on each side.  To determine why it was done this way, I removed the rear sight base and found the original roll pin hole on the right rear of the frame was drilled at an angle about 15 degrees from perpendicular to the frame.  This resulted in the drill bit breaking out of the frame on the right side in the wrong location (assuming the hole was drilled from left to right).  The resulting hole on the right side is at the rear corner of the frame.  This would have caused the frame to be rejected, since the hole would not align with the hole in the normal sight base.  The fix used by the gunsmith was to insert a flush-fitting metal plug in the large hole in the frame where the two piece rivet normally would have gone.  Then holes were drilled and tapped (one on each side of the frame) to allow the sight base to be screwed onto the frame with just the two screws.   Corresponding holes were drilled in the sight base.  The holes were offset so the base would not shift position.  There is a hole in the rear of the frame for the roll pin that would have gone through the rivet, but there is no roll pin present.  The result is functional, but different than the original configuration. 

The sight base was also not installed square to the frame.  The gunsmith did not spend the extra time required to elongate the holes in the sides of the base to get it to fit squarely.  Rather, the base sides were bent slightly resulting in a trapezoid shape to allow it to fit to the frame with the drilled holes.  The result is that the rear sight blade was cocked to the right.  When I reassembled the gun, I re-fitted the base to the frame by straightening the sides of the base to fit squarely on the frame, and elongated the holes in the sides of the base with a file so they would line up with the holes in the frame.  After final assembly, the rear sight is sturdily mounted and properly aligned. 

Other differences noted on the gun are as follows:

1.     The gold plating on the trigger, safety, and magazine release is a duller, more yellow, finish than on earlier push button guns, probably due to a different plating shop process or vendor.

2.     The metal polishing of the barrel and the sides of the frame and slide has a coarser finish than earlier push button guns.  The slide finger serrations have the top edges flattened by the polishing process.

3.     The roll stampings were applied to the frame and slide after the metal sides were sanded.  This resulted in raised edges of the letters above the surrounding metal compared to earlier models.

4.     There is no golden colored filling in the roll stamps. 

I performed a function test of the pistol on the firing range.  I loaded and fired a total of five strings of ten shots each using the magazine that came with the gun.  There were no malfunctions for feeding, firing, or ejecting the cases.  There was no need to adjust the feed lips.  The accuracy was as good as other High Standard pistols.  In conclusion, the pistol functioned well, but the appearance is of a lesser quality than earlier push button series 107 pistols.

 

 Left side of pistol:  Note the large screw holding the sight base to the frame.  Also, note the raised edges of the metal around the lettering on the frame and slide compared to the barrel markings. The grips are ambidextrous.

Right side of pistol:  The V suffix not in alignment with the rest of the serial number.  The screw holding the sight base to the frame is offset from the position of the screw on the other side.

 

Right photo:  Prior to reassembly,

I straightened the base and elongated

 the holes to allow proper fit.  Much better!

Left Photo:  The sight base was originally installed with the

 blade canted to the right.  The sides of the base were bent to allow

the holes in the base to align with the frame holes.

 

 Disassembled pistol with rear sight base removed.  The original rivet hole was plugged with a metal cylinder.  Holes were drilled and tapped for the screws to hold the base to the frame.  The sight base does not have the normal holes for the rivet and roll pins, but has one large hole on each side.

 

 Note the roll pin hole was drilled out of alignment with the frame.  This was the apparent reason for the frame being rejected during production of the series 107 pistols.